上海翻译公司|上海疏浚工程专业翻译(三)公司|上海译境翻译公司|疏浚工程英语词汇短语双语在线查询
短干锚 short shank anchor
多爪锚 grapnel anchor
双爪锚 double-flukes anchor
犁锚 plough anchor
单爪锚 one-fluke mooring anchor
燕尾锚(丹福锚) Danforth anchor
无杆锚 stockless anchor
霍尔锚 Hall’s anchor
有杆锚 stocked anchor
海军锚 admiralty anchor
活动锚 portable anchor
备用锚 spare anchor
尾锚 poop anchor
小锚 kedge anchor
中锚 stream anchor
首锚 bow anchor
锚 anchor
备用活塞 stock piston
旋转活塞 rotary piston
动力活塞 power piston
柱形活塞 plunger piston
油冷却活塞 oil cooling piston
补偿活塞 compensating piston
液缸活塞 bucket piston
平衡活塞 balance piston
活塞速度 piston velocity
活塞阀 piston valve
活塞冲程 piston stroke
活塞弹簧 piston spring
活塞杆十字头 piston rod cross head
活塞销 piston pin
活塞头 piston crown
活塞冷却系统 piston cooling system
活塞冷却管 piston cooling pipe
活塞衬套 piston bush
活塞螺栓 piston bolt
活塞本体 piston body
活塞筒 piston barrel
活塞杆 piston rod
活塞 piston
帽,盖 cap
活络接头螺母 union nut
圆缘螺母 collar nut
细齿螺母 serrated nut
对开螺母 half nut
螺帽 cap nut
蝶形螺母 butterfly nut
槽顶螺母 castle nut
自锁螺母 self-lock nut
防松螺母 lock nut
平顶螺母 flush nut
铣制螺母 milled nut
螺母 nut
细纹螺钉 fine thread screw
止动螺钉 stop screw
固定螺钉 set screw
凹头螺钉 socket screw
无头螺钉 headless screw
螺钉 screw
双头螺栓 stud bolt
调整螺栓 adjustable bolt
贯穿螺栓 tie-rod (through-bolt)
压紧螺栓 holding down bolt
系紧螺栓 anchor bolt
紧固螺栓 fastening bolt
压环螺栓 junk ring bolt
活节螺栓(紧固舱口盖用) dog bolt
镀锌螺栓 galvanized bolt
底脚螺栓 crab bolt
机制螺栓 turned bolt
圆头螺栓 round head bolt
六角头螺栓 hexagon (head) bolt
螺栓 bolt
空气压力控制阀 air pressure control valve
温度控制阀 temperature control valve
燃油快点阀 F.O. emergency shut off valve
倒车辅助阀 astern guardian valve
正车操纵阀 ahead maneuvering valve
调节阀 adjustable valve
截止阀,断流阀 stop valve (cut-off valve)
提升阀 poppet valve
(热)膨胀阀 (thermal) expansion valve
导阀 pilot valve
安全阀 safety valve (relief valve)
排气阀 exhaust valve
吸入阀 suction valve
起动阀 starting valve
主阀 master valve (main valve)
板阀,片阀 plate valve
闸(门)阀 gate valve
差动阀 differential valve
背压阀 back-pressure valve
应急阀 emergency valve
泥阀 mud valve
金氏-通海阀 Kingston valve (seal valve)
(通)大气阀 atmospheric valve
减压阀 reducing valve
节流阀 throttle valve
止回阀 check valve (non-return valve)
阀座 valve seat
阀瓣 valve flap
阀片、阀板 valve plate
阀杆导管 valve rod guide
阀衬套 valve liner
阀杆 valve stem
阀箱压盖 valve (chest) gland
阀盖 valve lid (valve cover)
阀盘 valve disc
阀箱 valve box
阀壳 valve casing
阀体 valve body
充填阀 charge valve
隔离阀 isolating valve
混合阀 mixing valve
转换阀 change (over) valve
旁通阀 by-pass valve
三通阀 three way valve
直通阀 through way valve
速闭阀 quick closing valve
弹簧阀 spring-loaded valve
浮动阀 floating valve
多口阀 multi-ported valve
双座阀 double seat valve
回转阀 rotating valve
滑簧 slide valve
多片簧阀 multiple leaf valve
针阀 needle valve
阀 valve
喷嘴环 nozzle ring
(管子的)膨胀圈 expansion ring
分度圈 index ring
隔圈,定距环 spacer ring (distance ring)
胀圈,填密环 packing ring
护圈 guard ring
紧圈 tightening ring
护油环 oil control ring
密封环 seal(ing) ring
止推环 thrust ring
减磨环 antifriction ring
止动环 stop ring
压缩环 compression ring
刮油环 oil (scraping) ring
支承环 carrier ring
耐磨环 wear ring
颈环,颈圈 neck ring
开口环 snap ring
活塞环 piston ring
环,圈 ring
弹簧座 spring retainer (spring seat)
锁簧 locking spring
压缩弹簧 compression spring
牵引弹簧 tension spring
放松弹簧 release spring
复原弹簧 returning spring
减震弹簧 shock absorber spring
缓冲弹簧 cushion spring
抗衡弹簧 counter (balance) spring
平衡弹簧 balance spring
调节弹簧 adjusting spring
细弹簧,游丝 hair spring
板簧 band spring
扁簧 flat spring
锥形弹簧 conical spring
圆柱弹簧 cylindrical spring
螺旋形弹簧 helical spring
弹簧 spring
轮缘 rim
轮福 arm of wheel
轮觳 boss, hub
滑轮 pulley
棘轮 ratchet
侧车凸轮(换向凸轮) astern cam (reversing cam)
正车凸轮 ahead cam
凸轮 cam
偏心轮 eccentric
链轮 sprocket (chain wheel)
滚轮导承 roller guide
滚轮 roller
齿条 rack (gear)
蜗杆 worm (endless screw)
中间齿轮(中速齿轮) intermediate gear
小齿轮 pinion
大齿轮 gear wheel
伞齿轮 bevel gear
斜齿轮,螺旋齿轮 screw gear (spiral gear, helical gear)
正齿轮 spur gear (spur wheel)
减速齿轮 reduction gear
变速齿轮 speed change gear
惰轮,空转齿轮 idler (idle gear, idling gear)
紧张轮 tension gear
定时齿轮 time (timing) gear
互换齿轮 interchangeable
轮子 wheel
齿轮 gear
摇臂 rock(er)arm (rocking arm)
臂 web (arm)
联(接)杆 linkage
油封 oil seal
衬套、轴衬 bush, bushing
轴承支架 bearing support
轴承箱 bearing box (bearing housing)
轴承座 bearing block
(滚珠轴承)外圈 outer race
(滚球轴承)内圈 inner race
推力块 thrust pad (shoe)
轴承座圈 bearing race
轴承衬 bearing bush
下轴(承)瓦 lower (bottom) bearing shell (half)
上轴(承)瓦 upper (top) bearing shell (half)
轴(承)瓦 bearing shell (half)
轴承本体 bearing body
轴承盖 bearing cap (cover)
耳轴承 trunnion bearing
(尾)轴轴承 (stern) shaft bearing
舵头舵承 rudder head bearing
上舵承 rudder carrier bearing
舵承 rudder bearing
挠性轴承 flexible bearing
法兰轴承 flange bearing
反向转动轴承 counter-rotating bearing
连杆轴承 connecting rod bearing
曲柄销轴承 crank pin bearing
十字头(销)轴承 crosshead (pin) bearing
锥形轴承 cone (conical) bearing
球轴承(滚珠轴承) ball bearing
滚针轴承 needle bearing
推力轴承 thrust bearing
主轴承(曲轴轴承) main bearing (crankshaft bearing)
轴承 bearing
推杆 push rod (tappet rod)
杆、手柄 lever
套筒 sleeve
柱塞 plunger
轴台 plumber block
回转轴 revolving shaft
摆(动)轴 pendulum shaft
实心轴 solid shaft
空心轴 hollow shaft
刚性轴 stiff shaft
挠性轴 flexible shaft
卷筒筒 drum shaft
蜗杆轴 wore shaft
副轴 counter shaft
从动轴 drive shaft
主动轴 (main) drive shaft
尾轴(螺旋浆轴) tail shaft (propeller shaft)
中间轴 intermediate shaft (tunnel shaft)
推力轴 thrust shaft
传动轴 transmission shaft
凸轮轴 cam shaft
轴法兰 shaft flange
轴系 shafting
轴线 shaft line
轴 shaft
泥浆输送管线 slurry pipeline
泥管闸阀 gate valve for pipeline
泥管旋动接头 pipeline swivel joint
磨耗报警传感器 wear alarm transmitter
摩擦阻力头曲线(图) graph of frictional resistance head
摩擦阻力 frictional resistance
压力阻力 pressure resistance
粘性阻力 viscous resistance
阻力系数 resistance coefficient
速度头 velocity head
吸入水头 suction head
球接头 ball joint
胶管接头 rubber hose connection
活动接头 moveable joint
水上排泥管长度 length of floating pipeline
排泥距离 range of soil discharge
船内吸泥管 in-hull suction pipeline
船尾排泥管旋转接头 assembly of dredge swivel pipe
船上排泥管 in-hull pressure pipeline
船上挖泥管 inboard dredge pipe
浮管上鹅颈接头 goose neck in floating pipeline
吸泥管活动接头 moveable joint in suction pipeline
排泥管活动接头 moveable joint in discharge pipeline
排泥管内摩擦阻力 friction in discharge pipeline
排泥管内沉淀 sedimentation in discharge pipeline
喷嘴 soil discharging nozzle
吸泥头 soil receiver suction end
排泥口 discharge end
伸缩接管 expansion joint
吸泥软管 suction hose
橡胶管 rubber hose
胶质挠性管 rubber sleeves for dredger
活动式吸泥管 articulated suction tube
易拆式吸管 easy disconnected suction pipe
挠性吸泥管 flexible suction tube
软管 hose
脂油管系 grease piping
潜管 submerged pipe
浮管 floating pipe
排泥弯管(可旋弯管) discharge elbow (swivel elbow)
排泥管水锤作用 water hammer of delivery pipe
排泥管真空通气阀 air inlet valve of delivery pipe
可潜排泥管 submerged pipeline
塑料排泥管 plastic delivery pipeline
自浮排泥管 self-floating pipeline
末端分支排泥管 pendant pipeline
排泥槽 chute
皮带排泥机 soil removal conveyer
皮带排送装置 disposal of soil with conveyer
排泥管水头损失 head loss of the delivery pipe
排泥槽起落装置 hoisting gear for glide chute
高架溜泥装置 gantry chute
排泥设备 soil discharging facility
排泥管特性曲线 characteristic curve of pipeline
排泥管工作流速 working velocity of pipeline
泥舱装泥管路 hopper-loading pipeline
排泥管支架 pipeline frame
排泥管接岸装置 shore connecting plant
陆上连接管 shore connection pipe
挠性管,软管 flexible pipe
耙吸管 drag pipe
吸泥管 (slurry) suction pipe
水上排泥管 floating (pontoon delivery) pipeline
排泥管 (slurry) discharge pipe
挖泥机械管系 piping of dredge machinery
套(节)管 socket pipe (thimble)
盘管 coil
循环水管系 circulating water piping
(排气)歧管 (exhaust) manifold
排气总管 exhaust pipe (main)
放气管 vent pipe
尾轴管 stern shaft pipe
回油管 return oil pipe
溢流管 overflow pipe
油位指示管 oil gauge pipe
加油管 oil filling pipe
润滑油管 lubricating pipe
液压管 hydraulic pipe
动力管 power pipe
燃油管 fuel (oil) pipe
喷射管 ejection pipe
淡水管 fresh water pipe
给水管 feed pipe
泄水管 drain pipe (blow pipe)
下降管 descent pipe
冷却管 cooling pipe
连接管 connecting pipe
循环管 circulating pipe
消防总管 fire main pipe
旁通管 by-pass (by-ath) pipe
十字管接头 cross pipe
S形弯管,鹅颈管 goose neck pipe
S形管接头 S (-bend) pipe
“乙”字管 pipe offset
U形管 U-pipe
T形管 T-pipe
Y形三通管,叉管 breeches pipe
支管 branch pipe
舱底水管 bilge pipe
压载水管 ballast pipe
增压管 ascending pipe
吸气管 air suction pipe
输气管 air delivery pipe
总管 main pipe
管路,管系布置 piping
管系,导管 pipeline
管、管路 pipe
浮动密封装置 floating seal arrangement
固定密封装置 fixed seal arrangement
锁定件 locking piece
伸缩节 expansion piece
压力补偿系统 pressure compensation system
主轴轴承润滑系统 shaft bearing lubrication system
轴封黄油润滑系统 shaft seal grease system
泥泵冲水系统 water flushing system
叶轮进口 impeller inlet
推力环 thrust ring
支承环 supporting ring
密封环 sealing ring
吸口衬环 suction nozzle liner
吸入端盖 suction cover
抗磨板 wearing plate
抗磨环 wearing ring
防磨衬套 wearing bush
压力件(卡簧) pressure piece
盖板 coverplate
隔板 separating plate
水室 water chamber
内泵壳 inner pump housing
外泵壳 outer pump housing
三分卡环 tripartite clamping ring
轴承托架 bearing pedestal
滚珠推力轴承 roller thrust bearing
滚柱轴承 roller bearing
叶轮轴承 impeller bearing
轴封 shaft seal
叶轮轴 impeller shaft
叶轮叶片 blade of impeller
叶轮 impeller
接力泵站 booster station
泥泵气蚀 cavitation of pump
泥泵叶轮叶片 sandpump impeller vanes
泥泵总扬程 total head of sandpump
泥泵衬板 wearing liner of dredge pump
泥泵水封箱 sealing water box of dredge pump
泵磨耗检查 inspection for pump wearing
泥泵试验 dredge pump test
泵的电动机 pump motor
泵的生产率 capacity of pump
泵的抽送率 pumpage
泵的接合器 pump adapter
泵的旁通路 pump bypass
泵止回球 pump check ball
泵排量试验 pump delivery test
泵样调整器 pumping adjuster
泵减载气蚀 pump load-drop cavitation
泵滤网护圈 pump screen retainer
泵阀压紧簧 pump valve pressing spring
泵小齿轮 pump pinion
泵吸入管 pump suction pipe
泵防松簧 pump check spring
泵用轴承 bearing in pump
泵的把手 pump handle
泵的气室 air dome of pump
泵的能率 duty of pump
泵的吸高 lift of the pump suction
泵的扬程 pump lift
泥泵磨损 dredge pump wearing
泥泵真空度 vacuum of dredge pump
流速曲线 speed curves
功率曲线 power curves
效率曲线 efficiency curves
流量扬程曲线 Q-H curves
泥泵压力扬程曲线 dredge pump manometric curves
泥泵特性曲线 dredge pump characteristic curves
泥泵设计 design of sandpump
泥泵构造 construction of sandpump
泵送上岸的装置 pump-ashore units
泵的有效压力 available pump pressure
泵入口过滤器 pump inlet strainer
泵进口止回阀 pump inlet check valve
泵吸入压头 pump suction head
泵吸入管道 pump suction line
泵吸入阀座 pump suction valve seat
泵的传动齿轮 pump drive gear
泵的导水管 pump water conduits
启动泵 priming pump
泵的压头 pump head
泵的性能 pump performance
泵的油封 pump oil seal
泵操纵杆 pump lever
泵扩散管 pump diffuser
泵排量 discharge of pump
泵压力计 pump pressure gauge
泵工作轮 pump wheel
泵排出管 pump main